Get started with Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM Development Platform
Unpacking
Remove the Development Platform from box and place above the ESD free area. Use anti-static pad/mat with proper grounding to place the Development Platform. Also make sure that, below deliverables are received without any physical damage.
Development kit contains:
- Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM Development Platform
- 12V, 5A Power Supply
- USB Debug cable
- Allen key
- Fan sink (Integrated with Development Platform)
Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM Development Platform
USB Debug Cable
12V, 5A Power Supply
Allen key
Safety Guidelines
Environmental Compliance
iG-G36M®-Zynq™ UltraScale+™ ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1 MPSoC SoM Development Platform is designed by using oHS and REACH compliant components and manufactured on lead-free production process.
ESD Protection
This development platform is ESD sensitive. Handle the product only in accordance with the installation instructions given in the manual. Therefore ESD precautions should be taken care during transport and handling. Must use a ESD ground strap or other grounded source before unpacking or handling the hardware.
Product Disposal
Check the local regulations for disposal of electronic products before disposing.
Get to know
Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM – Top view
1. PMIC Programming Header
2. 5V Fan connector
Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM – Bottom view
3. Board to Board connector 2
4. Board to Board connector 1
Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM Development Platform – Top view
1. Reset Button
2. DisplayPort Connector
3. JTAG Selection switch
4. Debug UART & JTAG Type-C
Connector
5. USB3.0 & 2.0 Type-C Connector
6. PCIe x4 Connector
7. Board to Board Connector 1
8. MicroSD Connector
9. Board to Board Connector 2
10. Power ON/OFF Switch
11. Power IN Connector
12. Ethernet Connector 1
13. Ethernet Connector 2
14. Boot Mode Selection Switch
15. DIP Switch
16. 60 Pin GPIO Header
17. FMC+ Connector
Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM Development Platform – Bottom view
18. RTC Coin Cell Holder
19. PMOD Connector
20. M.2 SATA Connector
Note: Not all of the connectors mentioned above are compatible with the Zynq™ UltraScale+™ MPSoC (ZU5/4/3T/3/2/1) SOM. Refer to the Development Kit’s datasheet for information on supported connectors and their detailed descriptions.
Download FTP Contents
All the technical resources of iG-G36M® Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM Development platform is available in iWave FTP server.
FTP Folder structure
For FTP Credentials, Contact : mktg@iwave-global.com
Note: Please make sure SW4.4 bit of Boot Mode Selection Switch Stays OFF (Logic High) always.
Boot Switch Setting
Make sure that On-SOM Boot Mode Switch (SW4) is set for eMMC boot as shown in below image.
SW4-Boot selection Switch
Debug Port Setting
The Zynq™ UltraScale+™ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM Development Platform has a built-in JTAG emulator. Both JTAG and Debug UART can be accessed via a single USB-C connector (J8).
Connect Type A end of USB cable to PC and Type-C end of USB cable to Development platform’s Debug USB Type-C Connector (J8) as shown below.
Install the driver for Debug Port in Host PC/Laptop using the
below link.
https://ftdichip.com/products/ft232rq/
How to configure
Use one of the terminal application depending on the operating system of the host machine:
On the command prompt of the Linux host machine, run the following command to determine the port number:
$ ls /dev/ttyUSB*
The smaller number is for Arm® Cortex®-A53 core and the bigger number is for Arm® Cortex ®-M4 core.
Minicom
Use the following commands to install and run the serial communication program (minicom as an example):
- Install Minicom using Ubuntu package manager.
$ sudo apt-get install minicom - Launch Minicom using a console window using the port number determined earlier.
$ sudo minicom -s - Configure Minicom as show in below figure
- Next step is to Power ON the board.
Install the driver for Debug USB Port in Host PC/Laptop using the below link.
http://ftdichip.com/drivers/vcp-drivers/
- Download Tera Term. After the download, run the installer and then return to this webpage to continue.
- Launch Tera Term. The first time it launches, it shows the following dialog. Select the serial option. Assuming your board is plugged in, there should be a COM port automatically populated in the list.
- Configure the Serial Port Settings.
Go to Setup –> Serial Port and change the settings as shown below.
- Verify that the connection is open. If connected, Tera Term shows something like below in its title bar.
- Next step is to Power ON the board.
Install the driver for Debug USB Port in Host PC/Laptop using the below link.
http://ftdichip.com/drivers/vcp-drivers/
- Download PuTTY. After the download, run the installer and then return to this webpage to continue.
- Launch PuTTY by either double clicking on the executable file you downloaded or from the Start menu, depending on the type of download you selected.
- Configure in the window that launches. Select the Serial radio button and ether the COM port number that you determined earlier. Also enter the baud rate, 115200
- Click “Open” to open the serial connection. Assuming the board is connected and you entered the correct COM port, the terminal window opens. If the configuration is not correct, puTTY alerts you.
- Next step is to Power ON the board.
JTAG Connection
iG-G36M®-Zynq™ UltraScale+™ ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1 MPSoC SoM Development platform Support JTAG interface through Debug and JTAG Type-C Connector (J8) in Carrier Board for MPSoC/FPGA Programming and debugging. JTAG-SMT4 Programming module in carrier board supports both JTAG and Debug UART functionality.
Powering ON
Connect the 12V power supply plug to the power connector (J2) of the Development platform as shown below and switch (J2) ON the power supply. Once power is applied to the Development platform, the power LEDs in Zynq UltraScale+ MPSoC(ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1) SOM and REN Carrier Board will glow as shown in the below image.
Warning:
- Do not try to connect any other Power Supply other than supplied along with the Development Platform.
- Do not plug or remove the Zynq UltraScale+ MPSoC (ZU5/ZU4/ZU3T/ZU3/ZU2/ZU1)SOM from carrier board with live power.
- Contact iWave, if power LEDs are not glowing or PS Error status LEDs are glowing.
Boot Screen
User must go through “Software User Guide” and get familiar with software section of iG-G36M®-Zynq-UltraScale+MPSoC-SOM
Once power is applied to the Development Platform as explained in the previous section, boot messages being displayed in the debug terminal of the PC/Laptop which is connected to the Development platform. Press any key in terminal immediately to see the command prompt of the Boot loader or wait until OS boots.
Command Prompt (Linux)
