Get started with Zynq UltraScale+ MPSoC ZU7/ZU5/ZU4 Development Platform
Unpacking
Remove the Development Platform from box and place above the ESD free area. Use anti-static pad/mat with proper grounding to place the Development Platform. Also make sure that, below deliverables are received without any physical damage.
Development kit contains:
- Zynq UltraScale+ MPSoC (ZU7/ZU5/ZU4) SOM Development Platform
- 12V, 5A Power Supply
- USB OTG cable
Zynq UltraScale+ MPSoC (ZU7/ZU5/ZU4) SOM Development Platform
USB OTG Cable
12V, 5A Power Supply
Safety Guidelines
Environmental Compliance
Zynq UltraScale+ MPSoC (ZU7/ZU5/ZU4) SOM Development Platform is designed by using RoHS and REACH compliant components and manufactured on lead-free production process.
ESD Protection
This development platform is ESD sensitive. Handle the product only in accordance with the installation instructions given in the manual. Therefore, ESD precautions should be taken care during transport and handling. Must use a ESD ground strap or other grounded source before unpacking or handling the hardware.
Product Disposal
Check the local regulations for disposal of electronic products before disposing.
Get to know
Zynq UltraScale+ MPSoC (ZU7/ZU5/ZU4) SOM – Top view
1. JTAG Header
2. FAN Header
3. PMIC Programming Header
4. Boot Mode Switch
5. Zynq US+ MPSoC
Zynq UltraScale+ MPSoC (ZU7/ZU5/ZU4) SOM– Bottom view
1. Board to Board connector 1
2. Board to Board connector 2
Zynq UltraScale+ MPSoC (ZU7/ZU5/ZU4) SOM Development Platform – Top view
Zynq UltraScale+ MPSoC (ZU7/ZU5/ZU4) SOM Development Platform– Bottom view
1. PMOD Connector 2
2. Board to Board Conn 1
3. PMOD Connector 1
4. JTAG Header
5. Board to Board Conn 2
6. PS IO Header
7. RESET Switch
8. ON/OFF Switch
9. Power Jack
10. Debug UART Connector
11. USB OTG Connector
12. GEM0 Ethernet Jack
13. GEM3 Ethernet Jack
14. Display Port
15. PS GTR Config Switch
16. SFP+ Connector
17. PCIe X1 Connector
18. SDI IN HD BNC Jack
19. SDI OUT HD BNC Jack
20. Standard SD Connector
21. USB Type C Connector
22. FMC Connector 1
23. CAN Header
24. FMC Voltage Select Switch
25. FMC Connector 2
26. RTC Battery Holder
27. M.2 SATA Connector
Download FTP Contents
All the technical resources of iG-G30D Zynq Ultrascale+ MPSoC (ZU7/ZU5/ZU4) SOM Development platform is available in iWave FTP server.
On Board Switch Setting
Make sure that On-SOM Boot Mode Switch (SW1) is set for eMMC boot as shown in below image.
Debug Port Setting
Connect TypeA end of USB cable to PC and MicroB end of USB cable to Development platform’s Debug USB MicroAB Connector (J5) as shown below.
Install the driver for Debug Port in Host PC/Laptop using the below link
https://ftdichip.com/products/ft232rq/
Setup the Debug Terminal parameters.
Baud Rate : 115200
Data bits : 8
Parity : None
Stop Bits : 1
Flow Control : None
Powering ON
Connect the 12V power supply plug to the power connector (J4) of the Development platform as shown below and switch ON the power supply.
Once power is applied to the Development platform, the power LEDs in Zynq Ultrascale+ MPSoC SoM and High Performance carrier board will glow as shown in the below image.
Warning:
1. Do not try to connect any other power supply other than supplied along with the Development platform.
2. Do not plug or remove the Zynq Ultrascale+ MPSoC / FPGA SOM from carrier board with live power.
3. Contact iWave if power status LEDs are not glowing or PS Error status LEDs are glowing.
Test Environment setup
Once power is applied to the Development Platform as
explained in the previous section, boot messages being displayed in the debug terminal of the PC/Laptop which is connected to the Development platform. Press any key in terminal immediately to see the command prompt of the Boot loader or wait until OS boots.
After OS boots, Login prompt being displayed in the debug terminal. Enter username and password as “root” to get the Linux command prompt as shown below.
Command Prompt (Linux)
Heat Sink Integration
iG-G30D Zynq Ultrascale+ MPSoC (ZU7/ZU5/ZU4)
SOM Development platform comes with Heatsink+Fan
attached to it. Makesure to power up the platform only with Heatsink+Fan attached.
Below is the Heatsink+Fan integration procedure for
reference.
Heatsink + Fan
Power Peel off Thermal Pad Sticker
JTAG Connection
iG-G30D Zynq Ultrascale+ MPSoC (ZU7/ZU5/ZU4) SOM Development platform Support JTAG interface in SOM and Carrier Board for MPSoC/FPGA Programming and debugging.
Example JTAG Cable which is tested with this Platform is mentioned below.
JTAG-HS2 Programming Cable
Part Number: 410-249
JTAG Connection to SOM
JTAG Connection to Carrier Board
