Get started with Zynq UltraScale+ MPSoC ZU19/ZU17/ZU11 Development Platform
Unpacking
Remove the Development Platform from box and place above the ESD free area. Use anti-static pad/mat with proper grounding to place the Development Platform. Also make sure that, below deliverables are received without any physical damage.
Development kit contains:
- Zynq UltraScale+ MPSoC (ZU19/ZU17/ZU11) SOM Development Platform
- 12V, 14A Power Supply
- USB OTG cable
Zynq UltraScale+ MPSoC (ZU19/ZU17/ZU11) SOM Development Platform
USB OTG Cable
12V, 14A Power Supply
Safety Guidelines
Environmental Compliance
Zynq UltraScale+ MPSoC (ZU19/ZU17/ZU11) SOM Development Platform is designed by using RoHS and REACH compliant components and manufactured on lead-free production process.
ESD Protection
This development platform is ESD sensitive. Handle the product only in accordance with the installation instructions given in the manual. Therefore, ESD precautions should be taken care during transport and handling. Must use a ESD ground strap or other grounded source before unpacking or handling the hardware.
Product Disposal
Check the local regulations for disposal of electronic products before disposing.
Get to know
Zynq UltraScale+ MPSoC (ZU19/ZU17/ZU11) SOM – Top view
1. 5V FAN Header
2. JTAG Header
3. Zynq US+ MPSoC (ZU11/17/19EG)
4. Boot Mode Switch
5. PMIC Programming Header
Zynq UltraScale+ MPSoC (ZU19/ZU17/ZU11) SOM– Bottom view
6. Board to Board connector 4
7. Board to Board connector 3
8. Board to Board connector 1
9. Board to Board connector 2
Zynq UltraScale+ MPSoC (ZU19/ZU17/ZU11) SOM Development Platform – Top view
Zynq UltraScale+ MPSoC (ZU19/ZU17/ZU11) SOM Development Platform– Bottom view
1. Firefly Connector
2. Firefly Power Connector
3. Board to Board Conn 4
4. Board to Board Conn 2
5. PMOD Connector 2
6. JTAG Header
7. RESET Switch
8. PMOD Connector 1
9. QSFP+ Connector
10. Power ON/OFF Switch
11. Power IN Connector
12. Debug Port
13. 20 Pin GPIO Header
14. USB OTG Connector
15. GEM0 Ethernet Jack
16. GEM3 Ethernet Jack
17. Display Port
18. PS GTR Config Switch
19. SFP+ Connector
20. PCIe x 1 Connector
21. SDI IN HD BNC Jack
22. SDI OUT HD BNC Jack
23. HDMI OUT Connector
24. CAN Header
25. HDMI IN Connector
26. USB Type C Connector
27. FMC Connector
28. Board to Board Conn 1
29. FMC+ Connector
30. Board to Board Conn 3
31. 12V FAN Header
32. RTC Battery Holder
33. Standard SD Connector
34. M.2 SATA Connector
35. SMA Connector 2
36. SMA Connector 1
Download FTP Contents
All the technical resources of iG-G35D Zynq Ultrascale+ MPSoC (ZU11/17/19EG) SOM Development platform is available in iWave FTP server.
On Board Switch Setting
Make sure that On-SOM Boot Mode Switch (SW1) is set for eMMC boot as shown in below image.
Heat Sink Fan Connection
iG-G35D Zynq Ultrascale+ MPSoC (ZU11/17/19EG) SOM Development platform comes with Heat Sink + Fan mounted on SOM.
Make sure that Heat Sink Fan is connected to 5V FAN connector (J1) in SOM as shown in the above figure. Do not connect the Heat Sink Fan to 12V FAN Connector in Carrier board
Debug Port Setting
Connect TypeA end of USB cable to PC and MicroB end of USB cable to Development platform’s Debug USB MicroAB Connector (J13) as shown below
Install the driver for Debug Port in Host PC/Laptop using the below link
https://ftdichip.com/products/ft232rq/
Setup the Debug Terminal parameters.
Baud Rate : 115200
Data bits : 8
Parity : None
Stop Bits : 1
Flow Control : None
Powering ON
Connect the 12V power supply plug to the power connector (J10) of the Development platform as shown below and switch ON the power supply.
Once power is applied to the Development platform, the power LEDs in Zynq Ultrascale+ MPSoC (ZU11/17/19EG) SOM and Ultra High Speed Carrier Board will glow as shown in the below image.
Warning:
1. Do not try to connect any other power supply other than supplied along with the Development platform.
2. Do not plug or remove the Zynq Ultrascale+ MPSoC (ZU11/17/19EG) SOM from carrier board with live power.
3. Contact iWave if power status LEDs are not glowing or PS Error status LEDs are glowing.
Test Environment setup
Once power is applied to the Development Platform as
explained in the previous section, boot messages being displayed in the debug terminal of the PC/Laptop which is connected to the Development platform. Press any key in terminal immediately to see the command prompt of the Boot loader or wait until OS boots.
iWave supports below mentioned Operating System Release for iG-G35D Zynq Ultrascale+ MPSoC (ZU11/17/19EG) Development platform.
After OS boots, Login prompt being displayed in the debug terminal. Enter username and password as “root” to get the Linux command prompt as shown below
Command Prompt (Linux)
